Just How to Install a Bathtub in Your Bathroom
Just How to Install a Bathtub in Your Bathroom
Blog Article
This great article in the next paragraphs pertaining to How to Install a Bathtub Yourself is incredibly intriguing. You should look it over.
Setting up a bathtub isn't specifically rocket science, yet it does need strong plumbing, woodworking, and occasionally, tiling skills. Changing an old bathtub with a brand-new one is likewise a moderately hard job. If the old tub is readily accessible, the job can move easily; if you have to open up a wall to get rid of the old tub and also position the new tub, the task is a lot harder. In either case, the task is within a house handyman's abilities, although you will need an assistant to move out the old tub and also set in the new one. See to it you have certified on your own for the job and fit trying it. Rather than working with a specialist to take over a halfway-completed project, it is far better to consider employing one prior to you begin. Chances are you might need an expert plumber to make tube links.
This write-up will certainly help you install a new tub in your shower room if you have actually currently bought a new bathtub and don't need to alter the setup of your previous water pipes.
Your tools and material checklist ought to comprise the following:
Planning for the Installation
First of all, the sustaining structure provided with the bathroom needs to be fitted (if called for) according to the supplier's instructions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is very important to see to it that if the faucet comes with a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bath, it is also practical to fit a sustaining plate under the taps device to prevent pressure on the bathtub.
Fit the versatile tap ports to the bottom of both taps making use of 2 nuts and olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet with the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Ensure you use every one of the provided washing machines.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom ought to currently be ready to be suited its last setting.
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your setup, then the first thing you need to do is detach the supply of water. After doing so, activate the taps to drain pipes any water continuing to be in the system. The procedure of getting rid of the existing taps can be quite problematic as a result of the limited gain access to that is usually the case.
Use a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipes to the taps. Have a cloth all set for the continuing to be water that will certainly originate from the pipelines. When the supply pipes have actually been removed, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single taps from turning during this process. When the faucets have actually been removed, the holes in the bath/basin will have to be cleaned up of any kind of old securing compound.
Prior to moving on to fit the new taps, contrast the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Installing the Tub
Making use of both wooden boards under its feet, put the tub in the called for position. The wood boards are useful in equally spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto four little factors.
The next objective is to make certain that the tub is leveled all round. This can be attained by checking the spirit level as well as readjusting the feet on the bathtub up until the level reads level.
To mount taps, fit the bottom of the outermost flexible tap port to the ideal supply pipe by making a compression join; after that do the very same for the other faucet.
Activate the water supply and inspect all joints and also brand-new pipework for leaks and tighten them if needed. Load the bathtub and likewise inspect the overflow electrical outlet and also the normal outlet for leaks.
Lastly, deal with the bathroom paneling as described in the producer's user's manual. Tiling as well as sealing around the tub must wait till the bath tub has been used at least once as this will settle it right into its final position.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will need a plastic port to avoid damages to the thread. One end of the port fits on the plastic tail of the tap and the various other end supplies a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will require reducing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, place the faucet in the installing hole in the bath/basin ensuring that the washing machines are in place in between the tap and also the sink. Protect the faucet in place with the manufacturer supplied backnut. Once the faucet is securely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular tap adapters. The former kind ought to be linked to the faucet ends first, tightening up only by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the area where the bath meets the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the installation can relocate enough to break an inflexible seal, creating the water to penetrate the wall between the bath and the tiling, resulting in problems with moisture as well as possible leaks to the ceiling below.
You can choose from a variety of coloured sealants to blend in your fixtures and installations. They are marketed in tubes and also cartridges, and also can securing spaces as much as a width of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of soaked paper or soft rope. Keep in mind to always load the tub with water before sealing, to permit the motion experienced when the tub remains in use. The sealant can fracture relatively early if you do not take into account this motion before securing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise easily offered on the market. It is a good idea to fit the floor tiles utilizing waterproof or waterproof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I have been very eager about How to Install a Bathtub Yourself and I'm hoping you appreciated my entry. Please set aside a second to distribute this blog if you enjoyed reading it. I treasure reading our article about A Step-by-Step Guide to Installing a Bathtub.
Request Your Service Report this page